DS AUDIO REPLACES DS-W2 WITH NEW THIRD GENERATION DS-W3

DS Audio’s inaugural optical cartridge, the DS-W1, was first launched in 2015. Now they are launching the latest model, the new DS-W3.

A year later, the brand announced the higher spec Master 1 and subsequently applied trickle-down technology to upgrade the ‘W’ model to the DS-W2. In 2020, the third generation of optical cartridges was launched with the flagship Grand Master, from which trickle-down tech has again been applied to the ‘W’ model, to create the new DS-W3.

DS Audio DS-W3 Optical Cartridge

DS AUDIO DS-W3 OPTICAL CARTRIDGE

The DS Audio DS-W3 optical cartridge sports a completely new design compared its predecessor and is very much an example of the brand’s ‘third generation’ technology first seen in the flagship Grand Master. Its optical system has been comprehensively re-engineered to deliver a number of benefits.

INDEPENDENT LEDS

Independent LEDs and photo-detectors for the left and right channels deliver a significantly increased output voltage: now 70mV compared to the previous 40mV. This new independent design has also made it possible to eliminate crosstalk, improving left and right channel separation. At the same time, the S/N ratio is much improved, resulting in a lower noise floor.

This new design also enables a smaller shading plate, which is reduced in both size and weight from 1.56mg to 0.74mg, because of the use of 99.9% pure beryllium rather than the previous aluminium.

DS AUDIO DS-W3 OPTICAL CARTRIDGE BORON CANTILEVER

The DS-W3 combines a boron cantilever with a line contact stylus. The cartridge’s body is constructed from aluminium with a structure crafted for maximum rigidity, while the internal wiring is 1.6 times thicker than that of the earlier second generation model, thus reducing impedance.

DS AUDIO EQUALIZER

Like all DS Audio optical cartridges, the DS-W3 requires its own equalizer/phono stage, which this new design also brings up to ‘third generation’ level. All internal components are optimized for third-generation cartridge technology, the thickness of the circuit board has increased from 1.6mm to 2.0mm, and the thickness of the copper tracks have been doubled from 35µm to 70µm. The equalizer offers both unbalanced and balanced outputs with a choice of four different low-frequency roll-off points ensuring that the DS-W3 will partner with any high-end HiFi system.

DS Audio DS-W3 Optical Cartridge equalizer

MADE IN JAPAN

Every DS Audio product is hand-made and quality assured, and every component tested and evaluated, by the company’s own in-house team of technicians in Japan.

DS AUDIO DS-W3 OPTICAL CARTRIDGE TECHNICAL SPECIFICATIONS

Body material Aluminium

Cantilever Boron

Stylus Line contact

Signal output Photo-electric conversion

Output signal level   > 70mV

Channel separation > 27dB (@ 1kHz)

Weight 7.9g

DS-W3 PHONO STAGE/EQUALIZER

Inputs RCA

Outputs RCA x 2, XLR x 2

Rated output voltage 500mV (@ 1kHz)

Output impedance RCA 120Ω, XLR 600Ω

Pre-amp input impedance  > 10Ω

Dimensions   450 (w) x 120 (h) x 435 (d) mm

Weight 13.5kg

DS AUDIO DS-W3 OPTICAL CARTRIDGE PRICING & AVAILABILITY

The DS Audio DS-W3 optical phono cartridge and phono stage/equalizer are available now, priced as follows (inc. VAT):

Cartridge and equalizer package price:  £12,995

Cartridge only: £4,995

Equalizer only: £9,495

DS Audio cartridges are fully compatible with any of the company’s accompanying phono stages/equalizers, allowing you to mix and match.

HiFi Pig Says: DS Audio really are seen as the pioneers of optical cartridges and have also shared their technology,read more here.